Drone Imagery Requirements for Cemetery Mapping
Planning a drone flight for your cemetery map? This page lists what to ask the operator for, so the file you receive can go straight onto your CemeteryBase map. Forward it to your drone operator as it is.
For a cemetery map, ask your drone operator for:
- 1One stitched, top-down orthomosaic of the whole cemetery, delivered as a georeferenced GeoTIFF.
- 2A resolution of 2 cm per pixel or better, flown leaf-off in even light.
- 3Survey-grade positioning (RTK/PPK or ground control points) and the accuracy report.
- 4Ground targets at the cemetery and section corners, with their coordinates in a spreadsheet.
LiDAR, 3D models and elevation data are not needed. Send us the file and we place it on your map and build the plots over it.
The drone deliverable: one cemetery orthomosaic
An orthomosaic is the single, seamless overhead image that mapping software (DroneDeploy, Pix4D, DJI Terra and others) stitches from the flight photos. It is the only file we need.
One stitched orthomosaic
A single top-down image of the whole cemetery, plus about 20 feet beyond the boundary on every side. Not the individual photos, and not a video.
GeoTIFF, georeferenced
A .tif file that carries its own position. Any standard coordinate system is fine (UTM, State Plane or latitude/longitude) as long as it is written into the file. Please tell us which one was used.
2 cm per pixel or better
About three quarters of an inch on the ground per pixel. Send the full-resolution export, not a reduced preview.
Natural colour, no markings
Ordinary colour imagery (RGB, 8-bit). No labels, north arrows, logos, grid lines or annotations drawn on the image.
Under 10 GB
JPEG or DEFLATE compression inside the GeoTIFF is fine and keeps the file small.
How to fly a cemetery for mapping
Timing and light matter more than equipment. These four choices decide how much of the ground is visible.
Straight down
Camera pointing straight down (nadir) for the whole flight, with the usual overlap for mapping. Angled shots are not needed.
Leaf-off
Fly between November and March where trees lose their leaves, so more of the ground shows through the branches.
Even light
An overcast day, or the middle of the day, so long shadows from trees and monuments do not hide the ground.
Beyond the boundary
Cover the surrounding roads, paths and fence lines. The edges of an orthomosaic are its least accurate part, and nearby landmarks help us confirm the position.
Positioning accuracy and ground targets for cemetery maps
A sharp image in the wrong place is not much use. Graves are only a few feet wide, so the position of the image matters as much as its detail.
Survey-grade positioning
RTK or PPK on the drone, or at least five surveyed ground control points. Without one of these the whole image can sit several feet off, which is wider than a grave.
The accuracy report
The processing report from the mapping software, showing the positioning method and the measured error.
Ground targets at the corners (recommended)
Visible targets at the corners of the cemetery and of each section, labelled, with the latitude and longitude of each one in a spreadsheet (decimal degrees). We place each section on these points.
Points under the trees (where needed)
Where tree cover hides the ground, a few GPS points taken on foot, such as the corner graves of the covered sections, also listed in the spreadsheet.
Drone mapping a cemetery with tree cover
A drone camera cannot see through branches. Where trees cover the ground, the image shows the trees. That does not stop the map from being built.
Your plots are drawn from your plat and lot numbering, then placed on the image section by section. Every lot appears on the map and links to its burial records, whether or not it sits under a tree. The drone image is the background.
For covered sections, ground targets and a few GPS points taken on foot give us what the camera cannot. With those, a wooded section is placed as accurately as an open one.
What a cemetery drone survey does not need
A cemetery plot map is flat. You can leave these out of the quote:
- LiDAR
- A point cloud
- A 3D model or mesh
- An elevation model (DSM or DTM)
- Oblique or 360° photos
- Video
A note to send your drone operator
Select the text below, copy it, and paste it into your quote request.
Drone imagery requirements for our cemetery map Deliverable - One stitched orthomosaic of the whole cemetery, plus about 20 ft beyond the boundary on every side - GeoTIFF (.tif), georeferenced; please state the coordinate system - 2 cm per pixel or better, full-resolution export - Natural colour (RGB, 8-bit), with no labels or annotations on the image - Under 10 GB (JPEG or DEFLATE compression is fine) Flight - Camera straight down (nadir) - Leaf-off season, overcast or even light, minimal shadow Positioning - RTK/PPK, or at least five surveyed ground control points - The accuracy / processing report - Ground targets at the cemetery corners and section corners, with the latitude and longitude of each (decimal degrees) in a spreadsheet - Where trees hide the ground: a few GPS points taken on foot, in the same spreadsheet Not needed - LiDAR, point cloud, 3D model, elevation model, oblique photos, video Delivery - Shared drive link or direct file transfer Full requirements: https://cemeterybase.com/drone-imagery-requirements
Cemetery drone imagery FAQ
What should I ask a drone operator for when mapping a cemetery?+
Ask for one georeferenced GeoTIFF orthomosaic of the whole cemetery at 2 cm per pixel or better, captured straight down in leaf-off conditions with even light, positioned with RTK/PPK or ground control points, and delivered with the accuracy report. Ground targets at the cemetery and section corners, with their coordinates in a spreadsheet, make the map more accurate.
Does a drone photo give me the location of every grave?+
Not by itself. A drone orthomosaic is a picture in which every pixel has a position. The graves are then drawn on top of it and linked to your burial records. CemeteryBase builds the plots from your plat or lot numbering and uses the drone image to put each section in the right place.
Can a cemetery with a lot of trees still be mapped from a drone?+
Yes. A camera cannot see through branches, so covered areas show as tree cover in the background image, but the plots are still on the map because they are drawn from your records and plat. Fly leaf-off, and add ground targets or a few GPS points on foot in the covered areas so those sections can be placed accurately.
Do I need LiDAR or a 3D model for a cemetery map?+
No. A cemetery plot map is flat. A top-down colour orthomosaic is the right product; LiDAR, point clouds, 3D models and elevation data are not used.
What if the operator can only provide a JPEG or PNG?+
A GeoTIFF is strongly preferred because it carries its own position. A high-resolution JPEG or PNG can still be used if it comes with the coordinates of at least four clearly visible points, but the placement is less accurate and takes longer.
Do I need a drone flight at all?+
No. A cemetery map can be built on existing satellite or state aerial imagery. A drone flight gives a much sharper and more current background, and better accuracy when it is flown with survey-grade positioning.
Who puts the drone image on the map?+
We do. Send us the file by shared link and CemeteryBase checks it against these requirements, places it on your cemetery map and builds the sections and plots over it as part of assisted setup.
Have drone imagery of your cemetery already?
Send us a link to the file. We check it against this list and tell you whether it is ready for your map or what to ask the operator to change.
Or book a 30-minute demo to see a cemetery map built on drone imagery.